Mercury Sable 2008 Bedienungsanleitung PDF herunterladen

one

Windshield / Wiper Washer

The multifunction lever controls the

windshield

wiper modes, speeds and the windshield washer. Rotate the end of the

control away from you to increase the speed of the wipers. Rotate the control towards

you to decrease the speed of the wipers.

For windshield washer control, push the end of the stalk briefly to cause a single swipe

of the wiper. With a quick push and hold, the wipers will swipe three times with washer fluid. With a long

push and hold, the wipers and washer fluid will activate for up to ten seconds

two

Speed Control For your speed control to work, you must press and release

the ON button. Pressing and releasing the OFF button disengages the system and

turns it off. To set a speed, press the ON button, accelerate to the desired speed and

press the SET+ button, then take your foot off the accelerator pedal. You can increase

your speed by pressing and releasing the SET+ button until you reach the desired

speed, increasing speed by 1 mph (1..6 km/h) with each tap. You can decrease speed

in the same way using the SET- button. Pressing the RSM (resume) button will automatically return the

vehicle to the previously set speed. To disengage the speed control, press the OFF or CNCL button or

depress the brake pedal.

three

Headlamp Control Turning the headlamp control clockwise to the first

position turns on the parking lamps, instrument panel lamps, license plate lamps and

the tail lamps. Continuing to turn the headlamp control to the second position turns

on the headlamps.

To use the autolamp light-sensitive, automatic on-off control for the headlamps, turn

the headlamp control counterclockwise. If the windshield wipers are turned on for a fixed period of time,

the exterior lamps will turn on with the headlamp control in the autolamp position. To turn autolamps off,

turn the control clockwise to the OFF position.

To activate the high beams, simply push the turn signal lever toward the instrument panel. Pull the lever

toward you to deactivate high beams. Use the same lever to activate the “Flash to Pass” feature. Pull the

lever toward you slightly to activate and release it to deactivate.

four

Foglamp Control

With the ignition on, the foglamps can be turned on when

the headlamp control is in the parking lamp, headlamp, or autolamp position and the high

beams are not on. Simply pull the headlamp control toward you to turn on the foglamps.

The foglamp indicator light will illuminate. The foglamps will not operate when the high

beams are activated.

Instrument Panel

2008 Mercury Sable

Instrument Cluster

Warning Lights and Message Center

Throttle Control/Transmission Lights The throttle control/transmission lights illuminates

when a powertrain fault has been detected. Contact your authorized dealer as soon as possible.

ABS Warning Light

In an emergency, apply continuous force to the brake pedal. Do not pump

the brakes. Any pulsation or mechanical noise you may feel or hear is normal. If the light doesn’t illuminate

or stays on, have your vehicle serviced. Normal braking is still functional unless the brake warning light

is also illuminated.

Speed Control Light The speed control light will Illuminate when the speed control is engaged.

It will turn off when the speed control system is disengaged. The controls for the speed control are

located on the steering wheel. Press and release the ON and OFF buttons to engage and disengage the

system. Speed control does not work at speeds below 30 mph (48 km/h). For more information, please

consult your Owner’s Guide.

Check Engine Light

The check engine indicator light illuminates when the ignition is first turned

to the ON position to check the bulb. If the lamp turns solid or blinks, the On Board Diagnostics System

has detected a malfunction. Drive in a moderate fashion (avoid heavy acceleration or deceleration) and

have your vehicle serviced immediately.

Brake System Warning Light To confirm the brake system warning light is functional, it will

momentarily illuminate when the ignition is turned to the ON position, when the engine is not running

or in a position between ON and START, or by applying the parking brake when the ignition is turned to

the ON position. If the brake system warning light does not illuminate at this time, seek service

immediately from your dealership. Illumination after releasing the parking brake indicates low brake

fluid level and the brake system should be inspected immediately by your servicing dealership.

Message Center With the ignition in the ON position, the message center displays important

vehicle information by constantly monitoring vehicle systems. You may select display features on the

message center for a display of status. The system will also notify you of potential vehicle problems

with a display of system warnings. For more information, please consult your Owner’s Guide.

2008 Mercury Sable

Instrument Panel

2008 Mercury

Sable

Get ready to redefine your

driving expectations. Your new Mercury

Sable is going to take your automotive

experience to a whole new level. And,

you get to go along for the ride in style,

comfort and with confidence. You know

your new Sable has attitude...and

you’re about to find out it also has

intelligence. Your new Sable was one

very smart choice.

This Quick Reference Guide was

designed to help you get to know your

new Sable. The perfect combination of

attitude, intelligence and style. That’s

your new Sable.

Feels good, doesn’t it?

five

Panel Dimmer Use this control to adjust the brightness of the instrument

anel and all applicable switches in the vehicle during headlamp and parking lamp

operation. Move the control to the full upright position, past the detent, to turn on the

nterior lamps.

six

Steering Wheel Audio Controls

(if equipped)

These controls allow you to adjust the radio and CD features

from the steering wheel. Press MEDIA to select AM, FM1, FM2

or CD. Press SEEK to access the next/previous strong station

or track on a CD. Press VOL+/- to adjust volume, and MUTE

to mute the volume.

A. Navigation/SYNC™ Hands Free Feature (if equipped):

Press and hold VOICE briefly until the icon appears on the

Navigation Display to use the voice command feature. Press

SEND or END to complete a voice command.

B. Navigation System Push To Talk (PPT) Hands Free Feature

(if equipped): Press and hold PTT briefly until the VOICE icon appears on the Navigation display to

use the voice command feature. Press PTT again to end a voice command.

C. SYNC™ System Hands Free Feature (if equipped): Press and hold VOICE briefly until the icon

appears on the display to use the voice command feature. Press and hold to send a call or text

message. Press OK to confirm your selection.

seven

Tilt Steering Column To adjust the steering wheel, push the

adjustment lever down to unlock the steering column. While the lever is down, tilt the

steering column to your desired position. Then, while holding the steering column in

place, pull the lever up to its original position to lock the steering column. Do not

adjust while driving.

Memory Feature

(if equipped) This feature will allow you to set two positions for

the driver's seat, power mirrors and adjustable pedals (if equipped). Set the position

by pressing the SET button (indicator will illuminate), then press the 1 or 2 button to

set the position to either Driver 1 or Driver 2. This memory setting can then be

recalled when you press the 1 or 2 button, enter Customer Code 1 or 2 on the keypad,

or when you press unlock on the remote entry system (one of your remote

transmitters is associated with Driver 1 and the other transmitter is associated with Driver 2)

A position

can be recalled in any gearshift position if the ignition is not in the RUN position or only in

P (Park) or N (Neutral) if the ignition is in the run position.

Power Mirrors To adjust your mirrors, rotate the control clockwise to adjust the

right mirror and counterclockwise to adjust the left mirror. Move the control in the

direction you wish to tilt the mirror. Then rotate the control to the center position to

lock the mirrors in place.

B C

1 2

Inhaltsverzeichnis

Seite 1 - Instrument Panel

one|Windshield / Wiper WasherThe multifunction lever controls thewindshieldwiper modes, speeds and the windshield washer. Rotate the end of thecontrol

Seite 2 - Essential Information

Quick Reference GuideFord Motor CompanyCustomer Relationship CenterP.O. Box 6248Dearborn, MI 481211-800-392-3673 (FORD)(TDD for the hearing impaired:

Kommentare zu diesen Handbüchern

Keine Kommentare

Mercury Sable 2008 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Autos Mercury Sable 2008 herunter. ayout 1 Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Autos Mercury Sable 2008